Click image for larger view |
 P/N: ETI0018-2070
Tactical Transit Case DC/AC Power Inverter
10,000 VA, 7000
Watts
24 VDC In, 120 VAC Out
This field-proven Series of Tactical Inverter® is supplied as a System incorporating numerous safety and operational advantages over other Inverter products sold into this market. The Inverter and associated connectors, circuit breakers and cables are housed in a rugged, water-resistant, tactical case. When the case is closed, all of the equipment is protected from the elements. Heavy-duty handles on the sides serve as both lifting points for deployment and as tie-down points to secure in a vehicle or aircraft. Optional permanent mounting bracket are available for fixed installations.
Setup of the Tactical Inverter System is a 'no tools' operation. The unit has been designed for rapid setup and tear down using quick-connect cable terminations. For example to connect to DC power on an HMMWV, Stryker, Abrams or other military vehicle with a NATO Slave connector, simply open the cover of the system case, plug the NATO Slave plug end of the cable into the vehicle's NATO connector and then plug the other end into the corresponding DC Input connector on the Tactical Inverter System. This can be done with an existing NATO Slave cable that some of these vehicle carry; or it can be done with a cable supplied from ETI. In either case, DC setup or tear down is a 2-minute or less operation.
The Inverter draws power from a 12, 24, or 48 VDC source (depending on Tactical Inverter model - see Technical Specifications section) and delivers a Computer-Grade true sine wave AC output voltage that is equal to or better than the voltage supplied by your local utility. When the DC voltage is within the operating range of the unit, the Inverter will continue to deliver AC power to the loads connected. If the DC voltage falls out of the specified range of operation, a Low or High DC Shutdown will occur respectively. This feature also protects any battery source from being discharged too low.
In addition to producing AC power, this series of Tactical Inverters also is available with a built-in 3-Stage Battery Charger that can operate simultaneously with Inverter operation. This Battery Charger can operate from 100/110/115/120 or 200/220/230/240 VAC source (depending on Tactical Inverter model - see Technical Specifications section) and charges 12, 24, or 48 VDC batteries (depending on Tactical Inverter model - see Technical Specifications section) per battery manufacture recommended charge levels and rates. |
Technical Specifications
| AC OUTPUT |
| Output
voltage: |
120 VAC
true sinewave
Optional 220 VAC |
| Output
rating: |
10,000
VA, 7000
watts continuous |
| Output
voltage regulation: |
± 3.0%
static regulation of nominal
-10% to +4.0% dynamic |
| Overload
surge capacity: |
2900
watts surge for 5 seconds |
| Output protection: |
Overcurrent
protection |
| Harmonic
distortion: |
Less than 3.0% THD |
| Output
frequency: |
60 Hz ± 0.5% crystal
controlled
Optional 50 Hz |
| Operational
status |
Status LCD
display, load level,
input volts/amps
audible alarm |
| DC INPUT |
| Input voltage
selection: |
Nominal 24
VDC |
| Input voltage
tolerance: |
21-32 VDC |
| Input control/protection: |
2-pole
Guarded DC Circuit Breaker,
Under/Over voltage,
Input Reverse Protection,
Low Voltage Disconnect (LVD) protecting source so
vehicle battery does not go below starting voltage |
| Input power
connection: |
Quick connect (1) NATO Slave female and
Quick connect
(1) Anderson Power Pole |
| Input power
cable: |
Uses standard NATO Slave male-male cable or
Optional
10' Anderson to NATO Slave male connector |
| DISTRIBUTION PANEL |
| Output
circuits: |
Four outputs
standard |
| Output protection: |
GFCI,
Ground Fault Circuit Interrupter |
| Output
control: |
Optional panel switches or breakers
Optional remote interlock ON/OFF control |
| Output
receptacles: |
NEMA 5-15R straight
blade standard |
| Ground connection: |
Quick connect jack |
| MECHANICAL |
| Enclosure type: |
Mil Grade Transit Case,
water tight to -30 ft w/pressure relief valve, lockable |
| Dimensions
( H x D x W ): |
19 in
(483 mm) x 20 in (508 mm) x 16.4 in (417 mm) |
Unit weight:
Inverter only
Cable only
Inverter with Cable together |
50 lb.
(23 kg)
15 lb.
(7 kg)
65 lb.
(30 kg) |
| Audible
noise: |
<47 dBA @ 5
ft., ANSI "A" scale |
| Cooling
type: |
Positive pressure fan.
thermostatically controlled, over temperature protection |
|
Air intake filter: |
Easy clean intake air
filter |
| ENVIRONMENTAL |
| Storage
temperature: |
-22° to
158° F ambient (-30° to 70° C),
lower/higher optional |
| Operating
temperature: |
32° to
140° F ambient (0° to 60° C
) |
| Operating
humidity: |
0 to 95%
relative humidity (non-condensing) |
| Storage
elevation: |
Up to 40,000
ft (12,192 m) |
| Operating
elevation: |
Up to 10,000
ft (3,048 m) |
| STANDARDS |
| United
States: |
Meets UL-1741
and 458 |
| Canada: |
Meets CSA 107.1 safety
requirements |
| EMI Protection: |
EMI/RFI
FCC Part 15, Class B standard |
| OPTIONAL ACCESSORIES |
| |
Input
Cables, Ground Cables w/ Clamp, Ground
Rod Kit, Power Distribution Units |
|
